c142494 asked:

1/2 hp volts 115/230 amps 9.5-4.75 circa 10/1986

serial 1-440-8

Question posted courtesy of: Elsie

Caz asked:

hi I have a Nutool 800W Belt Sander, and cant figure out how to replace the belt. i searched the nternet but with no look, just wondered if anyone had one and knew how to do it. thanks

Question posted courtesy of: Charlie

athorgarak asked:

The tos I am looking for, even if I need to find a collector, are very small power tools (jig saw, circular saw, drill, sander etc) they are made of a good quality metal and feel like real, adult tools. they came in little yellow or grey (I forget which) cases that doubled as the power pack (they needed ‘D’ batteries installed in the case) and the tool plugged into the case.
I really, REALLY want to find a set of these for my son (and, I admit, for myself)
ANY help is greatly appreciated

Question posted courtesy of: Warren

sherry4833 asked:

Looking at a Cordless Power tool, by GRIP, not familiar with that brand of power tools. Anyone own a GRIP, and how do you compare it to a SKIL, or similar brand Power Tool?

Question posted courtesy of: Javier

huuie asked:

i also have some 240v power tools,which ones can i leagilly use on site or in joinery workshops as in wrokshops here ,we can only use 240v,as on site its 110v..do you have the same systmes in place there or is it all the same??

Question posted courtesy of: Jacob

Akaash S asked:

(a) sand in a circular motion
(b) apply pressure to the sander
(c) hold the job with one hand while sanding
(d) use the machine only when it attains full speed

Question posted courtesy of: Andrea

pb&j asked:

I’m interested in buying one, will it sharpen blades?

Question posted courtesy of: Lillie

daycare aide asked:

hedge trimmers,johnsonred chain saaw, 1700,sacs domer weed wacker,sears variable speed drill, portable hand saw, sears air compressor(new), belt sander, orbital sander, orbital car polisher,lea blower, leaft chipper &mulcher, 5 hp battery charger, sears power lawn mower, contractors wheelbarrow,truck loading ramps, hydraulic jack, sears 199 pc socket set, firestorm musket 50 caliber,winchester 30/30 rifle,fishing equipment, prussian sword,beer stein, paintings, camera & lens, boch trumpet, cast iron ash tray, bedroom set, record collection, homelite chainsaw, 28 special revolver smith & wesson, 32/40 carbine rifle winchester, 12 gauge shotgun, 22 caliber ruger pistol,22 caliber marlin rifle, 9mm walther pistol, 12 gauge 36″ shotgun, 12 gauge shotgun mausburg, 30/06 winchester model 70 with 3/9 leopolde scope, 8mm mauser rifle, 7.86 sks rifle, penn state university captain’s chair, 2 recurve bows, thompsons musket firestorm 50 cal, 30/30 winchester rifle, baot, 2 weber gas grills, piano
roll top desk, coach and loveseat, couch and futon,sony tv, tv, upright freezer, beer-tap refrigrator,,refrigeraator,refrigerator,maple dresser, silverware, 442 oldsmobile, weilder weight machine, snow blower, 16 hp gravely tractor

Question posted courtesy of: Christian

Julia Collen asked:

Can this power tools be used for small home building work .

Question posted courtesy of: Curtis

James H asked:

I am planning to rebuild a fence using common cedar fence boards. These are sold wet and rough. The last time I built, I cured the lumber for 3 months. I used a belt sander to smooth all sides. It came out really nice, but the sanding was no fun: 3 days of vibration, “sawdust-snowman”, inhaling cedar dust, cedar splinters in my eyes. At the time I told myself, “next time I am buying/renting a machine to smooth these boards”.

I was thinking about a portable surface planer and rigging a vacuum exhaust. But I am not sure that the planer can handle all the warping cedar fence boards tend to have. Would a surface planner work for my application?

I’ve also seen surface drum sanders, and I know these are specifically designed for this application. But it seems like there are only commercial (ie >$500) machines available? Any ideas?

Question posted courtesy of: Agnes